The 6YL-95 screw oil press is a highly efficient machine used for extracting oil from various oil-bearing seeds. Proper installation of the screw worms is essential for the machine’s optimal performance. This detailed guide will walk you through the step-by-step process of installing the screw worms in your 6YL-95 screw oil press, ensuring your machine runs smoothly and efficiently.
Tools and Materials Needed
Before starting the installation work, please prepare the following tools and materials: wrench, screwdriver, lubricating oil, safety goggles and gloves, new screw, asbestos wire, raw tape, locking nut.
Step-by-Step Guide to Installing the Screw Worms in a 6YL-95 Screw Oil Press.
1. Turn Off the Machine and Disconnect the Power
Safety first! Ensure the machine is completely turned off and disconnected from the power source to avoid accidental startups during the installation process.
2. Remove the Outer Cover.
Using a wrench and screwdriver, carefully remove the outer cover of the oil press. This will expose the internal components, including the area where the screw worms will be installed.
3. Remove the Old Screw Worms.
Loosen Bolts and Nuts: Use the wrench to loosen and remove the bolts and nuts securing the old screw worms.
Remove the Old Screw Worms: Carefully take out the old screw worms, ensuring not to damage any other parts. If the screw worms are stuck, gently tap them to loosen.
4. Inspect and Clean the Installation Area.
Before installing the new screw worms, inspect the surrounding components for any signs of wear or damage. Replace any worn-out parts if necessary. Clean the installation area thoroughly to remove any debris and old oil residue.
5. Install the New Screw Worms.
Stand the Screw Shaft Upright: Position the screw shaft vertically with the thin end facing upwards.
Attach the Retaining Ring: Install the retaining ring onto the thin end of the screw shaft.
Install the Screw Worms: Place the new screw worms onto the shaft one by one, starting from 1 to 7 in sequence. Then, attach the slag discharge head.
Insert Asbestos Cord: Fill the gaps between the screw worms with asbestos cord. This helps to prevent oil and slag from seeping through.
Wrap with Teflon Tape: Wrap a layer of Teflon tape around the screw shaft to further seal the gaps and prevent leakage.
Secure with Locking Nut: Tighten the locking nut to hold the screw worms and other components in place securely, to prevent oil residue from entering the pressing screw hole and affecting subsequent disassembly.
6. Apply Lubricating Oil.
Apply a thin layer of lubricating oil to the new screw worms to ensure smooth operation and reduce friction during the pressing process.
7. Reassemble the Outer Cover.
Reattach the outer cover of the oil press, ensuring all bolts and nuts are tightly secured. This will prevent any operational issues and maintain the integrity of the machine.
8. Test Run the 6YL-95 Screw Oil Press.
Reconnect the power and start the machine. Observe its operation to ensure the new screw worms are installed correctly and there are no abnormal sounds or issues. If any problems arise, stop the machine immediately and address them.
Essential Tips for Maintaining Your 6YL-95 Screw Oil Press.
Regular Inspections: Perform regular inspections and maintenance on other parts of the oil press to prolong its lifespan.
Proper Handling: If you are not familiar with the machine’s structure, seek assistance from a professional technician to avoid damage or injury.
Safety Gear: Always wear protective gear, such as safety goggles and gloves, during the maintenance process.
Conclusion
Correct installation of the screw worms in your 6YL-95 screw oil press is crucial for ensuring the machine’s optimal performance and longevity. By following this detailed guide, you can ensure a smooth and safe installation process. Regular maintenance and timely replacements are key to keeping your oil press running efficiently. If you encounter any difficulties, refer to the user manual or contact the manufacturer for technical support.
